| 22380CAW33C3 SKF MINING MACHINERY BEARINGS | s:77.787 mm; d2:155.575 mm; A1:136.525 mm; J min.:333.375 mm; H1:120.65 mm; L:422.275 mm; J max.:368.3 mm; Limiting speed:1900 r/min; Basic dynamic load rating C:408 kN; J1:63.5 mm; H2:69.85 mm; A:117.475 mm; B:155.575 mm; Attachment bolt diameter G:19.05 mm; H:247.65 mm; da:112.713 mm; Mass bearing unit:32.3 kg; S:0.794 mm; |
| 23144CAW33C3 SKF MINING MACHINERY BEARINGS | B:6.00 mm; Grease Speed Rating Open/Shielded n1:36000 rpm; Oil Speed Rating Open/Shielded n2:43000 rpm; D:19.0000 mm; Basic Static Radial Load Rating Co:950 N; Basic Dynamic Radial Load Rating C:2210 N; Fillet Radius ra:0.30 mm; Accessories:Two Seals; Sealed Speed Rating n3:26000 rpm; d:5.000 mm; |
| Z-508726.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | da max.:111.2 mm; D:160 mm; Mass plain bearing:6.8 kg; Basic dynamic load rating C:655 kN; α:13 °; C:55 mm; Da min.:141.5 mm; Design (sliding contact surface combination):Steel/steel; Da max.:153.3 mm; r2 min.:1 mm; ra max.:1 mm; Specific dynamic load factor K:100 N/mm²; r1 min.:1 mm; d:100 mm; Sealing solution:Triple-lip seals; B:85 mm; Specific static load factor K0:500 N/mm²; b:11.5 mm; |
| 23148CAW33C3 SKF MINING MACHINERY BEARINGS | Bore Diameter D:20 mm; Outher Width C:14 mm; Dimension S:12.7 mm; Basic Dynamic Radial Load Rating:10600 N; Inner Width B:31.0 mm; Set Screw Size SSS:M6*0.75*5; Max Fillet Rad. MFR:0.6 mm; Dimension D3:28.20 mm; Outside Diameter D2:47 mm; Basic Static Radial Load Rating Co:6550 N; Weight W:0.14 kg; |
| 4R3232 NTN ROLL NECK BEARINGS for ROLLING MILL | r, r1,2 min.:1.1 mm; B:35 mm; Mass inner ring:0.58 kg; F:100 mm; d:85 mm; |
| NJ2336/C4 SKF MINING MACHINERY BEARINGS | D:85.0000 mm; B:10.00 mm; Sealed Speed Rating n3:4500 rpm; Basic Dynamic Radial Load Rating C:11700 N; d:65.000 mm; Oil Speed Rating Open/Shielded n2:8500 rpm; Fillet Radius ra:0.60 mm; Basic Static Radial Load Rating Co:11000 N; Grease Speed Rating Open/Shielded n1:7000 rpm; Accessories:One Shield; |
| NJ2348 SKF MINING MACHINERY BEARINGS | Basic dynamic load rating C:237 kN; Calculation factor e:0.44; Da max.:139.5 mm; a:36.627 mm; Ca min.:4 mm; C:30.162 mm; Calculation factor Y:1.35; da max.:104 mm; ra max.:5 mm; B:36.322 mm; db min.:112.5 mm; Db min.:141 mm; Da min.:128 mm; d:95.25 mm; d1 ≈:121.61 mm; r3,4 min.:3.3 mm; rb max.:3.3 mm; D:152.4 mm; Basic static load rating C0:305 kN; Cb min.:9.5 mm; |
| 22318CAW33C3 SKF MINING MACHINERY BEARINGS | Limiting value e:0.2; da max.:230 mm; Axial load factor Y:0.6; ra max.:3 mm; D:320 mm; Calculation factor kr:0.15; Reference speed:2200 r/min; Limiting speed:3600 r/min; Fatigue load limit Pu:88 kN; Basic static load rating C0:850 kN; Fw:217 mm; D1 ≈:278.6 mm; Da max.:302.2 mm; Mass bearing:14.6 kg; C:52 mm; Basic dynamic load rating C:720 kN; r1,2 min.:4 mm; |
| 313812W KOYO ROLL NECK BEARINGS for ROLLING MILL | Cap bolt, SAE grade:8; Da:309.999 mm; L:628.65 mm; PG:1/4 NPT; H2:69.85 mm; P60°:345 kN; Stabilizing ring:2 x 38151-40; R2:37.306 mm; H1:179.4 mm; P150°:113 kN; RG:3/4 NPT; P90°:207 kN; P120°:127 kN; P180°:133 kN; Max. speed for PosiTrac Plus seal:800 r/min; Housing:SAFS 040 KA; Initial grease fill:878.85 g; da:182.563 mm; Mass pillow block:156 kg; J min.:492.125 mm; |
| 230RV3301 NSK ROLL NECK BEARINGS for ROLLING MILL | D:110.0000 mm; Oil Speed Rating n2:5300 rpm; Grease Speed Rating n1:4000 rpm; Fillet Radius ra:2.00 mm; d:50.000 mm; Basic Dynamic Radial Load Rating C:95200 N; Basic Static Radial Load Rating Co:95000 N; Accessories:One Shield & Snap-Ri; B:47.60 mm; Sealed Speed Rating n3:4000 rpm; |
| Z-522742.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Calculation factor Y1:3.2; r1,2 min.:7.5 mm; D1 ≈:941 mm; d3:830 mm; B5:112 mm; d1:670 mm; d2 ≈:816 mm; Calculation factor Y2:4.8; ra max.:6 mm; B2:90 mm; db min.:736 mm; Reference speed:300 r/min; b:22.3 mm; Limiting speed:560 r/min; Mass bearing + sleeve:860 kg; Fatigue load limit Pu:965 kN; K:12 mm; D:1030 mm; B1:342 mm; Basic dynamic load rating C:8669 kN; |
| Z-524289.02.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Fatigue load limit Pu:0.98 kN; B:51.6 mm; d:44.45 mm; A1:15 mm; Limiting speed:4000 r/min; Db2:118 mm; GN:1/4-28 SAE-LT; DN:6.5 mm; J6:129 mm; J7:35.5 mm; A:43 mm; Recommended tightening torque for grub screw:16.5 N·m; Recommended diameter for attachment bolts, inch G:0.625 in; R1:28.5 mm; L:143 mm; N:18 mm; A5:33 mm; s1:32.6 mm; T:55.5 mm; Da:125.4 mm; |