| NJ2336/C4 SKF MINING MACHINERY BEARINGS | D:85.0000 mm; B:10.00 mm; Sealed Speed Rating n3:4500 rpm; Basic Dynamic Radial Load Rating C:11700 N; d:65.000 mm; Oil Speed Rating Open/Shielded n2:8500 rpm; Fillet Radius ra:0.60 mm; Basic Static Radial Load Rating Co:11000 N; Grease Speed Rating Open/Shielded n1:7000 rpm; Accessories:One Shield; |
| 190RV2701 NSK ROLL NECK BEARINGS for ROLLING MILL | Tolerance shaft:f7 m/s; B:55 mm; Coefficient of friction µ min.:0.08; Specific static load factor K0:120 N/mm²; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7 m/s; d:65 mm; Coefficient of friction µ max.:0.15; Mass bushing:0.26 kg; D:70 mm; Specific dynamic load factor K:40 N/mm²; Permissible sliding velocity v max.:1 m/s; |
| 23160CAW33C3 SKF MINING MACHINERY BEARINGS | J6:960 mm; s:30 mm; J1:220 mm; Eye bolt, size:2 x M 36; P150°:2500 kN; P0°:6100 kN; P55°:8000 kN; J:870 mm; da:400 mm; L:1040 mm; A1:360 mm; Appropriate attachment bolt, size G:36 mm; Cap bolt, size:M 36x240; P120°:2900 kN; Initial grease fill, 20%:7 kg; H1:360 mm; Bearing (basic designation):23084 K; ba min.:146 mm; Labyrinth seal:2 x TS 84; Q180°:2100 kN; |
| 22328CAKW33C3 SKF MINING MACHINERY BEARINGS | Initial grease fill:765.45 g; P90°:113 kN; Cap bolt recommended tightening torque:1220 N·m; Mass pillow block:62.8 kg; PG:1/4 NPT; P150°:68.1 kN; P120°:73.8 kN; End plug (suffix Y):EPR 13; Da:240 mm; h:63.5 mm; P60°:189 kN; L:466.725 mm; P180°:84.5 kN; Cap bolt, SAE grade:8; ba:48.419 mm; A1:133.35 mm; Appropriate attachment bolt size G:0.875 in; R1:79.375 mm; Taconite seal:TER 108; |
| 23144CAW33C3 SKF MINING MACHINERY BEARINGS | B:6.00 mm; Grease Speed Rating Open/Shielded n1:36000 rpm; Oil Speed Rating Open/Shielded n2:43000 rpm; D:19.0000 mm; Basic Static Radial Load Rating Co:950 N; Basic Dynamic Radial Load Rating C:2210 N; Fillet Radius ra:0.30 mm; Accessories:Two Seals; Sealed Speed Rating n3:26000 rpm; d:5.000 mm; |
| 4R382 NTN ROLL NECK BEARINGS for ROLLING MILL | Basic Static Radial Load Rating Co:104000 N; d:101.600 mm; Basic Dynamic Radial Load Rating C:59200 N; Fillet Radius ra:1.00 mm; Set:Quadruplex Set DFDT; Lateral Eccentricity Max LE:0.003 mm; D:145.0000 mm; B:88.90 mm; |
| NJ2348 SKF MINING MACHINERY BEARINGS | Basic dynamic load rating C:237 kN; Calculation factor e:0.44; Da max.:139.5 mm; a:36.627 mm; Ca min.:4 mm; C:30.162 mm; Calculation factor Y:1.35; da max.:104 mm; ra max.:5 mm; B:36.322 mm; db min.:112.5 mm; Db min.:141 mm; Da min.:128 mm; d:95.25 mm; d1 ≈:121.61 mm; r3,4 min.:3.3 mm; rb max.:3.3 mm; D:152.4 mm; Basic static load rating C0:305 kN; Cb min.:9.5 mm; |
| 31419 KOYO ROLL NECK BEARINGS for ROLLING MILL | d3 max.:131.902 mm; B4:21.438 mm; Mass adapter sleeve assembly:2 kg; G:99.517 mm; Hydraulic nut:HMVC 20E; B:19.304 mm; d:100 mm; B1:72.619 mm; d1:85.725 mm; Threads per inch:12; Sleeve:S 20x3.3/8; |
| 22360CAW33C3 SKF MINING MACHINERY BEARINGS | J max.:279.4 mm; L:330.2 mm; P120°:21.8 kN; PG:1/8 NPT; Ca:57.785 mm; Da:140 mm; P150°:19.6 kN; A2:209.55 mm; P60°:60.5 kN; N1:19.05 mm; R1:53.181 mm; h:36.513 mm; Cap bolt, SAE grade:8; Stabilizing ring:2 x SR-1613; Mass pillow block:17.1 kg; Pa:6.49 kN; RG:3/8 NPT; P90°:36 kN; Cap bolt recommended tightening torque:298.3 N·m; Max. speed for Taconite seal:1400 r/min; |
| NU2328C3 SKF MINING MACHINERY BEARINGS | J min.:131.762 mm; Mass bearing unit:3.65 kg; J max.:152.4 mm; B:59.531 mm; H:109.537 mm; Basic dynamic load rating C:102 kN; A:58.737 mm; Limiting speed:5300 r/min; L:187.325 mm; Attachment bolt diameter G:12.7 mm; da:42.862 mm; S:0.794 mm; H1:53.975 mm; s:29.766 mm; H2:33.337 mm; |
| 4R4426 NTN ROLL NECK BEARINGS for ROLLING MILL | d3 max.:155.702 mm; Hydraulic nut:HMVC 26E; Sleeve:S 3026x4.3/8; Threads per inch:12; G:129.692 mm; d1:111.125 mm; B4:25.4 mm; B:22.479 mm; B1:81.966 mm; d:130 mm; Mass adapter sleeve assembly:3.4 kg; |
| 4R6819 NTN ROLL NECK BEARINGS for ROLLING MILL | Mass bearing unit:1.2 kg; Recommended diameter for attachment bolts, inch G:0.5 in; Limiting speed:1100 r/min; T:46.4 mm; Basic static load rating C0:15.3 kN; Da:88.9 mm; J7:15 mm; J6:106 mm; A1:13 mm; s1:25.4 mm; Recommended tightening torque for grub screw:6.5 N·m; Housing material:Cast iron; H:156 mm; Db1:88 mm; L:96 mm; B4:6 mm; Db2:96 mm; d:34.925 mm; Hexagonal key size for grub screw N:3.969 mm; |