| Z-506962.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Fillet Radius ra:1.00 mm; d:100.000 mm; Fillet Radius rb:0.60 mm; Grease Speed Rating n1:8000 rpm; B:40.00 mm; Basic Static Radial Load Rating Co:127000 N; Basic Dynamic Radial Load Rating C:95600 N; Oil Speed Rating n2:12000 rpm; D:140.0000 mm; |
| 22230CAW33C3 SKF MINING MACHINERY BEARINGS | d1:240 mm; D:400 mm; ra max.:3 mm; da max.:326 mm; Basic static load rating C0:2850 kN; Ca min.:3.4 mm; r1,2 min.:4 mm; Misalignment factor k1:0.122; Basic dynamic load rating C:1760 kN; Fatigue load limit Pu:232 kN; B2:34 mm; d2 ≈:305 mm; D1 ≈:367 mm; d3:310 mm; Operating clearance factor k2:0.096; B5:46 mm; Reference speed:1300 r/min; db min.:272 mm; Limiting speed:1800 r/min; Da min.:349 mm; |
| 23252CAKW33C3 SKF MINING MACHINERY BEARINGS | s1:22.2 mm; Limiting speed:6300 r/min; A3:3.2 mm; Thread grub screw G2:1/4-28 UNF; Rα:45 °; H:141.5 mm; Hexagonal key size for grub screw N:3.175 mm; GN:1/4-28 SAE-LT; R1:21 mm; Recommended tightening torque for grub screw:4 N·m; Basic dynamic load rating C:19.5 kN; J:116.5 mm; Fatigue load limit Pu:0.475 kN; A:32.5 mm; Db2:83 mm; L:83 mm; DN:6.5 mm; N4:2 mm; d:30.163 mm; Basic static load rating C0:11.2 kN; |
| 22338CAW33C3 SKF MINING MACHINERY BEARINGS | α:124 °; D:220 mm; Permissible sliding velocity v max.:0.5 m/s; Tolerance shaft:e7; B:120 mm; D1:235 mm; d:200 mm; Permissible sliding velocity v min.:0 m/s; Specific dynamic load factor K:25 N/mm²; Coefficient of friction µ min.:0.08; Coefficient of friction µ max.:0.15; B1:10 mm; h:202.5 mm; Tolerance housing:H7; Specific static load factor K0:45 N/mm²; a:6 mm; Mass bushing:7 kg; |
| 23260CAW33C3 SKF MINING MACHINERY BEARINGS | H:39 mm; Oil:2 500 min-1; Grease:1 900 min-1; D:100 mm; dynamic Cr:141.700 kN; d1:100 mm; rs (min):1.1 mm; static Cor:243.000 kN; D1:47 mm; d:45 mm; Pu:11.050 kN; |
| Z-508727.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Appropriate attachment bolt size G:1 in; Stabilizing ring:SR-34-0; P180°:92.5 kN; End plug (suffix Y):EPR 18; H1:179.375 mm; A1:171.45 mm; H2:69.85 mm; P120°:85.9 kN; Da:309.999 mm; PG:1/4 NPT; P60°:234 kN; J max.:549.275 mm; Pa:56 kN; Eye bolt:2 x 3/8-16 UNC; R1:115.888 mm; J1:107.95 mm; H:360.363 mm; h:54.769 mm; Cap bolt, SAE grade:5; Mass pillow block:132 kg; |
| 23180CAKW33C3 SKF MINING MACHINERY BEARINGS | D:72 mm; Basic static load rating C0:15.3 kN; Calculation factor kr:0.025; Fatigue load limit Pu:0.655 kN; Da max.:65 mm; d:35 mm; D2 ≈:64.05 mm; ra max.:1 mm; Basic dynamic load rating C:27 kN; Limiting speed:6300 r/min; Calculation factor f0:13.8; da min.:42 mm; d2 ≈:43.574 mm; da max.:43.2 mm; r1,2 min.:1.1 mm; B:17 mm; Mass bearing:0.3 kg; |
| 22352CAW33C3 SKF MINING MACHINERY BEARINGS | Permissible sliding velocity v min.:0 m/s; Tolerance shaft:h9; Tolerance housing:H7; Permissible sliding velocity v max.:1 m/s; Specific dynamic load factor K:40 N/mm²; D:17 mm; d:15 mm; Specific static load factor K0:80 N/mm²; Coefficient of friction µ max.:0.15; Mass bushing:0.0011 kg; B:15 mm; Coefficient of friction µ min.:0.06; |
| 40FC2817 KOYO ROLL NECK BEARINGS for ROLLING MILL | r1 min.:0.6 mm; l3 min.:65 mm; d2 max.:104 mm; C1 max.:28 mm; Basic dynamic load rating C:127 kN; d4 ≈:65 mm; Material constant KM:330; l5 ≈:30 mm; l7 min.:55 mm; d:45 mm; α:7 °; l4 max.:219 mm; h1:165 mm; Mass rod end:3.2 kg; Specific dynamic load factor K:100 N/mm²; w:55 mm; Basic static load rating C0:224 kN; dk:60 mm; B:32 mm; G:M 45x3; |
| 22332CAW33C3 SKF MINING MACHINERY BEARINGS | B:30.20 mm; Oil Speed Rating n2:6300 rpm; Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:4800 rpm; Basic Static Radial Load Rating Co:58500 N; Grease Speed Rating n1:4800 rpm; d:50.000 mm; D:90.0000 mm; Basic Dynamic Radial Load Rating C:53900 N; Accessories:Two Seals & Snap-Rin; |
| NU2330C4 SKF MINING MACHINERY BEARINGS | Pa:81.4 kN; Appropriate attachment bolt size G:1.5 in; ba:96.838 mm; Cap bolt recommended tightening torque:400 N·m; H1:241.3 mm; P120°:160 kN; PG:1/4 NPT; Stabilizing ring:2 x A8898; Eye bolt:2 x 1/2-13 UNC; h:69.85 mm; Mass pillow block:247 kg; J min.:628.65 mm; RG:1 NPT; A1:222.25 mm; P90°:254 kN; Cap bolt, SAE grade:5; P150°:145 kN; P60°:423 kN; R1:130.175 mm; Da:399.999 mm; |
| 4R461 NTN ROLL NECK BEARINGS for ROLLING MILL | Basic Dynamic Radial Load Rating C:179000 N; Grease Speed Rating Open/Shielded n1:2100 rpm; Fillet Radius ra:2.50 mm; D:230.0000 mm; d:130.000 mm; Basic Static Radial Load Rating Co:216000 N; B:40.00 mm; Oil Speed Rating Open/Shielded n2:2600 rpm; Accessories:Without Accessories; |