| 4R4426 NTN ROLL NECK BEARINGS for ROLLING MILL | d3 max.:155.702 mm; Hydraulic nut:HMVC 26E; Sleeve:S 3026x4.3/8; Threads per inch:12; G:129.692 mm; d1:111.125 mm; B4:25.4 mm; B:22.479 mm; B1:81.966 mm; d:130 mm; Mass adapter sleeve assembly:3.4 kg; |
| 22232CAW33C3 SKF MINING MACHINERY BEARINGS | Oil Speed Rating n2:4000 rpm; Oil Speed Rating Open/Shielded n2:4000 rpm; Basic Static Radial Load Rating Co:108000 N; Grease Speed Rating n1:3400 rpm; Sealed Speed Rating n3:2400 rpm; d:90.000 mm; Fillet Radius ra:2.50 mm; Basic Dynamic Radial Load Rating C:143000 N; Accessories:One Seal; D:190.0000 mm; B:43.00 mm; Grease Speed Rating Open/Shielded n1:3400 rpm; |
| 160RV2302 NSK ROLL NECK BEARINGS for ROLLING MILL | Tolerance shaft:f7 m/s; Tolerance housing:H7 m/s; Coefficient of friction µ min.:0.08; Permissible sliding velocity v min.:0 m/s; Permissible sliding velocity v max.:1 m/s; Mass bushing:0.017 kg; D:23 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:120 N/mm²; d:20 mm; Specific dynamic load factor K:40 N/mm²; B:20 mm; |
| Z-527104.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Oil Speed Rating n2:6300 rpm; D:120.0000 mm; d:65.000 mm; Oil Speed Rating Open/Shielded n2:6300 rpm; Grease Speed Rating n1:5300 rpm; B:23.00 mm; Basic Dynamic Radial Load Rating C:55900 N; Grease Speed Rating Open/Shielded n1:5300 rpm; Basic Static Radial Load Rating Co:40500 N; Accessories:Two Seals; Sealed Speed Rating n3:3600 rpm; Fillet Radius ra:1.50 mm; |
| 22348CAW33C3 SKF MINING MACHINERY BEARINGS | d:20.000 mm; Accessories:No Shield, no Seal,; D:52.0000 mm; Basic Static Radial Load Rating Co:20000 N; B:25.40 mm; Basic Dynamic Radial Load Rating C:23800 N; Fillet Radius ra:1.00 mm; Grease Speed Rating n1:8500 rpm; Oil Speed Rating n2:12000 rpm; Sealed Speed Rating n3:8500 rpm; |
| 220RV3101 NSK ROLL NECK BEARINGS for ROLLING MILL | Pa:22.2 kN; Stabilizing ring:2 x 36053-50; A1:120.65 mm; Housing:SSAFS 028 KA; Da:210 mm; Mass pillow block:61.2 kg; R1:79.375 mm; H1:133.35 mm; RG:1/2 NPT; h:46.038 mm; H:257.175 mm; End plug (suffix Y):EPR 27; Ca:72.619 mm; A2:190.5 mm; P90°:149 kN; Labyrinth ring:2 x LOR 122; da:125.412 mm; P180°:107 kN; Cap bolt:5/8-11 UNC; P60°:249 kN; |
| NJ2338/C4 SKF MINING MACHINERY BEARINGS | F:425 mm; D:560 mm; Pu:151.940 kN; s:6 mm; d2 (max):mm; b:mm; r1s (min):5 mm; B:82 mm; rs (min):5 mm; d2:380 mm; b1:mm; Dynamic (Ca):1166 kN; E:mm; Static (Coa):1982 kN; |
| 22234CAW33C3 SKF MINING MACHINERY BEARINGS | B:10.00 mm; Grease Speed Rating n1:19000 rpm; d:17.000 mm; Fillet Radius ra:0.30 mm; Oil Speed Rating n2:24000 rpm; D:35.0000 mm; Basic Dynamic Radial Load Rating C:8520 N; Basic Static Radial Load Rating Co:4650 N; Fillet Radius rb:0.10 mm; |
| 370RV5211 NSK ROLL NECK BEARINGS for ROLLING MILL | Calculation factor Y2:2.1; Calculation factor e:0.48; Calculation factor Y0:1.4; Mass bearing:110 kg; Calculation factor Y1:1.4; Design variant/feature:TQOS/GWISI; Basic static load rating C0:6400 kN; r3,4 min.:3.3 mm; Basic dynamic load rating C:2550 kN; Comparative axial load rating CFa:166 kN; B:254 mm; T:254 mm; r1,2 min.:1 mm; Comparative radial load rating CF:710 kN; D1 ≈:420 mm; d1 ≈:362 mm; |
| Z-512764.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Labyrinth ring (dc shaft position):LOR 37; Ca:39.014 mm; P180°:19.1 kN; Initial grease fill:107.73 g; Cap bolt:2 x 1/2-13 UNC; Labyrinth ring (db shaft position):LOR 55; RG:1/8 NPT; Da:120 mm; Housing:SAF 213; R2:15.875 mm; Pa:12 kN; Mass pillow block:9.07 kg; PG:1/8 NPT; db:77.787 mm; P90°:30.2 kN; N1:19.05 mm; H:147.637 mm; H1:76.2 mm; PosiTrac Plus contact element (db shaft position):B10724-53; |
| 180RV2601 NSK ROLL NECK BEARINGS for ROLLING MILL | Accessories:Seal & Snap-Ring; Fillet Radius ra:0.64 mm; Grease Speed Rating n1:22000 rpm; B:10.00 mm; D:32.0000 mm; Basic Static Radial Load Rating Co:3100 N; Oil Speed Rating n2:28000 rpm; Oil Speed Rating Open/Shielded n2:28000 rpm; Sealed Speed Rating n3:15000 rpm; Basic Dynamic Radial Load Rating C:6890 N; d:12.000 mm; Grease Speed Rating Open/Shielded n1:22000 rpm; |
| 29FC21155 KOYO ROLL NECK BEARINGS for ROLLING MILL | Cap bolt recommended tightening torque:813.5 N·m; Max. speed for Taconite seal:590 r/min; R2:39.688 mm; Eye bolt:2 x 3/8-16 UNC; N1:28.575 mm; P90°:236 kN; ba:65.088 mm; Initial grease fill:623.7 g; End plug (suffix Y):EPR 16; Da:269.999 mm; PG:1/4 NPT; J max.:463.55 mm; L:539.75 mm; Pa:32.7 kN; da:134.938 mm; Housing:SAFS 530; Appropriate attachment bolt size G:1 in; Taconite seal:TER 127; |