| Z-508726.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | da max.:111.2 mm; D:160 mm; Mass plain bearing:6.8 kg; Basic dynamic load rating C:655 kN; α:13 °; C:55 mm; Da min.:141.5 mm; Design (sliding contact surface combination):Steel/steel; Da max.:153.3 mm; r2 min.:1 mm; ra max.:1 mm; Specific dynamic load factor K:100 N/mm²; r1 min.:1 mm; d:100 mm; Sealing solution:Triple-lip seals; B:85 mm; Specific static load factor K0:500 N/mm²; b:11.5 mm; |
| 23238CAW33C3 SKF MINING MACHINERY BEARINGS | Basic Static Radial Load Rating Co:500000 N; B:74.00 mm; Basic Dynamic Radial Load Rating C:358000 N; Accessories:Two Shields & Snap-R; Sealed Speed Rating n3:780 rpm; Grease Speed Rating Open/Shielded n1:1200 rpm; Oil Speed Rating Open/Shielded n2:1500 rpm; d:300.000 mm; Fillet Radius ra:3.00 mm; D:460.0000 mm; |
| 68FC48350D KOYO ROLL NECK BEARINGS for ROLLING MILL | Coefficient of friction µ max.:0.1; Mass bushing:0.026 kg; Permissible sliding velocity v min.:0.25 m/s; Specific static load factor K0:20 N/mm²; Coefficient of friction µ min.:0.05; Permissible sliding velocity v max.:5 m/s; Tolerance shaft:h8; d:15 mm; D:20 mm; Tolerance housing:H7; Specific dynamic load factor K:10 N/mm²; B:30 mm; |
| Z-507735.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Da max.:541 mm; Fatigue load limit Pu:57 kN; H:80 mm; Minimum load factor A:67; Basic dynamic load rating C:553 kN; Basic static load rating C0:3600 kN; r1,2 min.:2.1 mm; ra max.:2 mm; D1 ≈:504 mm; d1 ≈:596 mm; D:600 mm; Reference speed:560 r/min; Limiting speed:800 r/min; Mass bearing (including seat washer where applicable):47 kg; da min.:559 mm; d:500 mm; |
| 23130CAW33C3 SKF MINING MACHINERY BEARINGS | Basic Interchange:-; Basic Radial Load Rating-Static SCO:48600 lbf; Accessories:Mast Guide Type- 307; Basic Radial Load Rating-Dynamic DC:13600 lbf; Basic Interchange BCA:-; Basic Interchange NDH:-; Basic Interchange NSK:-; Basic Interchange MCGILL:-; Basic Interchange SPLIT:-; |
| Z-527104.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Oil Speed Rating n2:6300 rpm; D:120.0000 mm; d:65.000 mm; Oil Speed Rating Open/Shielded n2:6300 rpm; Grease Speed Rating n1:5300 rpm; B:23.00 mm; Basic Dynamic Radial Load Rating C:55900 N; Grease Speed Rating Open/Shielded n1:5300 rpm; Basic Static Radial Load Rating Co:40500 N; Accessories:Two Seals; Sealed Speed Rating n3:3600 rpm; Fillet Radius ra:1.50 mm; |
| 22338CAW33C3 SKF MINING MACHINERY BEARINGS | α:124 °; D:220 mm; Permissible sliding velocity v max.:0.5 m/s; Tolerance shaft:e7; B:120 mm; D1:235 mm; d:200 mm; Permissible sliding velocity v min.:0 m/s; Specific dynamic load factor K:25 N/mm²; Coefficient of friction µ min.:0.08; Coefficient of friction µ max.:0.15; B1:10 mm; h:202.5 mm; Tolerance housing:H7; Specific static load factor K0:45 N/mm²; a:6 mm; Mass bushing:7 kg; |
| 190RV2701 NSK ROLL NECK BEARINGS for ROLLING MILL | Tolerance shaft:f7 m/s; B:55 mm; Coefficient of friction µ min.:0.08; Specific static load factor K0:120 N/mm²; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7 m/s; d:65 mm; Coefficient of friction µ max.:0.15; Mass bushing:0.26 kg; D:70 mm; Specific dynamic load factor K:40 N/mm²; Permissible sliding velocity v max.:1 m/s; |
| 313824 KOYO ROLL NECK BEARINGS for ROLLING MILL | Mass housing:69.5 kg; J:430 mm; J6:470 mm; Oil seal:2 x TSD 3036 U; P90°:1000 kN; Oil level, max.:54 mm; P55°:2100 kN; A1:180 mm; H:333 mm; Locating ring:2 x FRB 17/280; Cap bolt, rec. tightening torque:350 N·m; J1:100 mm; Q120°:1800 kN; Ca:108 mm; Q150°:1040 kN; A:226 mm; H1:170 mm; H2:70 mm; Appropriate attachment bolt, rec. tightening torque:665 N·m; Appropriate attachment bolt, size G:24 mm; |
| 160RV2302 NSK ROLL NECK BEARINGS for ROLLING MILL | Tolerance shaft:f7 m/s; Tolerance housing:H7 m/s; Coefficient of friction µ min.:0.08; Permissible sliding velocity v min.:0 m/s; Permissible sliding velocity v max.:1 m/s; Mass bushing:0.017 kg; D:23 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:120 N/mm²; d:20 mm; Specific dynamic load factor K:40 N/mm²; B:20 mm; |
| 22322CAW33C3 SKF MINING MACHINERY BEARINGS | D:500.0000 mm; d:320.000 mm; Basic Static Radial Load Rating Co:1630000 N; Basic Dynamic Radial Load Rating C:761000 N; Grease Speed Rating n1:770 rpm; Oil Speed Rating n2:1300 rpm; Fillet Radius ra:3.00 mm; B:142.00 mm; Fillet Radius rb:1.00 mm; |
| Z-543975.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | d1:220 mm; Da max.:480 mm; Limiting speed:1300 r/min; db min.:257 mm; d3:300 mm; Calculation factor Y1:2.2; D:500 mm; Calculation factor e:0.31; Calculation factor Y0:2.2; B:155 mm; d2 ≈:303 mm; Basic static load rating C0:4000 kN; Ba min.:11 mm; D1 ≈:423 mm; B1:199 mm; K:12 mm; Basic dynamic load rating C:3229 kN; Reference speed:950 r/min; b:22.3 mm; Mass bearing + sleeve:170 kg; |