| 22252CAW33C3 SKF MINING MACHINERY BEARINGS | Grease Speed Rating n1:3600 rpm; Basic Static Radial Load Rating Co:106000 N; Basic Dynamic Radial Load Rating C:88000 N; D:120.0000 mm; Oil Speed Rating n2:4800 rpm; Fillet Radius ra:1.50 mm; B:38.10 mm; d:65.000 mm; Sealed Speed Rating n3:3600 rpm; Accessories:Two Shields; |
| 22330CAW33C3 SKF MINING MACHINERY BEARINGS | Oil Speed Rating Open/Shielded n2:3200 rpm; d:160.000 mm; D:220.0000 mm; Grease Speed Rating Open/Shielded n1:2600 rpm; Basic Dynamic Radial Load Rating C:92300 N; Sealed Speed Rating n3:1700 rpm; Basic Static Radial Load Rating Co:98000 N; Fillet Radius ra:2.00 mm; B:28.00 mm; Accessories:One Seal; |
| 23164CAW33C3 SKF MINING MACHINERY BEARINGS | Basic Dynamic Radial Load Rating:5730 lbf; Dimension H1:1.8750 in; Thread Diameter G:1/2-13; Shaft Diameter D:1 7/16 in; Dimension S1:1.0000 in; Insert Bearing IB:ZMaRC; Basic Static Radial Load Rating Co:3440 lbf; Dimension F:0.7500 in; Width A:1.8750 in; Distance J:3.2500 in; Weight W:4.50 lb; Height H:3.7500 in; Dimension L:4.1250 in; |
| 22322CAW33C3 SKF MINING MACHINERY BEARINGS | D:500.0000 mm; d:320.000 mm; Basic Static Radial Load Rating Co:1630000 N; Basic Dynamic Radial Load Rating C:761000 N; Grease Speed Rating n1:770 rpm; Oil Speed Rating n2:1300 rpm; Fillet Radius ra:3.00 mm; B:142.00 mm; Fillet Radius rb:1.00 mm; |
| 23238CAKW33C3 SKF MINING MACHINERY BEARINGS | Height G:3.938 in; Bolt Pattern C:0.55 in; Shaft C/L Distance F:1 31/32 in; Bolt Pattern D:2 3/4 in; Frame Size B:16 in; Length H:0.625 in; Frame Accepts These Shaft Sizes (Bearing Bore):40 mm; Travel:9; Bolt Pattern E:14 1/2 in; Frame Size A:5 1/4 in; |
| Z-527634.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Reference speed:180 r/min; Minimum load factor A:2900; Fatigue load limit Pu:208 kN; Da max.:1495 mm; D1 ≈:1408 mm; Limiting speed:260 r/min; d1 ≈:1622 mm; ra max.:6 mm; H:180 mm; D:1630 mm; Basic dynamic load rating C:1820 kN; Basic static load rating C0:22000 kN; da min.:1535 mm; Mass bearing (including seat washer where applicable):665 kg; d:1400 mm; r1,2 min.:8 mm; |
| 23152CAW33C3 SKF MINING MACHINERY BEARINGS | Mass bushing:0.001 kg; D:8 mm; Coefficient of friction µ min.:0.05; Coefficient of friction µ max.:0.1; Permissible sliding velocity v min.:0.25 m/s; B:6 mm; Specific dynamic load factor K:10 N/mm²; Tolerance shaft:h8; d:4 mm; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; Specific static load factor K0:20 N/mm²; |
| 340RV4801 NSK ROLL NECK BEARINGS for ROLLING MILL | Da:100 mm; ba:26.988 mm; Appropriate attachment bolt size G:0.625 in; Ca:30.785 mm; P60°:44.9 kN; J max.:209.55 mm; Cap bolt recommended tightening torque:81.3 N·m; Cap bolt, SAE grade:5; da:46.038 mm; P180°:19.1 kN; H:133.35 mm; Pa:4.14 kN; Bearing limiting speed:8500 r/min; Housing:SAF 511; H1:69.85 mm; N1:19.05 mm; Cap bolt:2 x 1/2-13 UNC; P90°:27.1 kN; Mass pillow block:7.85 kg; |
| 313812W KOYO ROLL NECK BEARINGS for ROLLING MILL | Cap bolt, SAE grade:8; Da:309.999 mm; L:628.65 mm; PG:1/4 NPT; H2:69.85 mm; P60°:345 kN; Stabilizing ring:2 x 38151-40; R2:37.306 mm; H1:179.4 mm; P150°:113 kN; RG:3/4 NPT; P90°:207 kN; P120°:127 kN; P180°:133 kN; Max. speed for PosiTrac Plus seal:800 r/min; Housing:SAFS 040 KA; Initial grease fill:878.85 g; da:182.563 mm; Mass pillow block:156 kg; J min.:492.125 mm; |
| 22248CAW33C3 SKF MINING MACHINERY BEARINGS | A2:304.8 mm; H1:241.3 mm; Housing:SAW 244; PG:1/4 NPT; J max.:708.025 mm; Max. speed for PosiTrac Plus seal:600 r/min; S:4.763 mm; L:831.85 mm; Stabilizing ring:SR-44-38; h:80.963 mm; Initial grease fill:2749.95 g; A1:222.25 mm; Ca:153.797 mm; P150°:145 kN; Cap bolt, SAE grade:5; J min.:628.65 mm; R1:130.175 mm; N1:41.275 mm; End plug (suffix Y):EPR 24; RG:1 NPT; |
| 22360CAW33C3 SKF MINING MACHINERY BEARINGS | J max.:279.4 mm; L:330.2 mm; P120°:21.8 kN; PG:1/8 NPT; Ca:57.785 mm; Da:140 mm; P150°:19.6 kN; A2:209.55 mm; P60°:60.5 kN; N1:19.05 mm; R1:53.181 mm; h:36.513 mm; Cap bolt, SAE grade:8; Stabilizing ring:2 x SR-1613; Mass pillow block:17.1 kg; Pa:6.49 kN; RG:3/8 NPT; P90°:36 kN; Cap bolt recommended tightening torque:298.3 N·m; Max. speed for Taconite seal:1400 r/min; |
| 4R3821 NTN ROLL NECK BEARINGS for ROLLING MILL | Mass lock nut:132 kg; h:28 mm; d3:800 mm; Associated spanner:TMFN 600-750; Associated eyebolt for handling:M 12; G:Tr 630x6; d2:685 mm; B5:120 mm; b:50 mm; d1:730 mm; B:95 mm; |