| 24172CAW33C3 SKF MINING MACHINERY BEARINGS | Attainable speed for grease lubrication:27000 r/min; b:1.4 mm; Basic dynamic load rating C:11.7 kN; C2:2.5 mm; r1,2 min.:1 mm; Preload class C GC:630 N; ra max.:1 mm; Ball diameter Dw:7.144 mm; db min.:44.6 mm; Calculation factor f2B:1.03; Calculation factor (back-to-back, face-to-face) X2:0.67; a:20.3 mm; Mass bearing:0.19 kg; Static axial stiffness, preload class C:169 N/µm; dn:51.6 mm; Calculation factor e:0.68; |
| 22318CAW33C3 SKF MINING MACHINERY BEARINGS | Limiting value e:0.2; da max.:230 mm; Axial load factor Y:0.6; ra max.:3 mm; D:320 mm; Calculation factor kr:0.15; Reference speed:2200 r/min; Limiting speed:3600 r/min; Fatigue load limit Pu:88 kN; Basic static load rating C0:850 kN; Fw:217 mm; D1 ≈:278.6 mm; Da max.:302.2 mm; Mass bearing:14.6 kg; C:52 mm; Basic dynamic load rating C:720 kN; r1,2 min.:4 mm; |
| Z-502894.02.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Reference grease quantity Gref:5.4 cm³; Calculation factor f0:15.4; Calculation factor fHC:1.02; r1,2 min.:1.1 mm; D:95 mm; Ball diameter Dw:11.112 mm; Basic dynamic load rating C:40.3 kN; d:60 mm; Calculation factor f2A:1; Basic static load rating C0:34.5 kN; Preload class A GA:150 N; rb max.:0.6 mm; Db max.:91.8 mm; B:18 mm; Calculation factor f1:1; r3,4 min.:0.6 mm; Static axial stiffness, preload class C:148 N/µm; |
| 4R3226 NTN ROLL NECK BEARINGS for ROLLING MILL | F:1053 mm; D:1220 mm; Basic dynamic load rating C:2640 kN; r1,2 min.:6 mm; da min.:1025 mm; Basic static load rating C0:6550 kN; Fatigue load limit Pu:400 kN; Limiting value e:0.2; Axial load factor Y:0.6; ra max.:5 mm; Reference speed:400 r/min; D1 ≈:1146 mm; d1 ≈:1072 mm; B:100 mm; Da max.:1196 mm; Limiting speed:530 r/min; Mass bearing:269 kg; db min.:1080 mm; Calculation factor kr:0.2; |
| NU2334MC3 SKF MINING MACHINERY BEARINGS | Fillet Radius ra:1.00 mm; B:16.00 mm; Grease Speed Rating Open/Shielded n1:10000 rpm; Oil Speed Rating Open/Shielded n2:13000 rpm; Accessories:Two Shields; Grease Speed Rating n1:10000 rpm; Sealed Speed Rating n3:7500 rpm; Oil Speed Rating n2:13000 rpm; d:30.000 mm; D:62.0000 mm; Basic Static Radial Load Rating Co:11200 N; Basic Dynamic Radial Load Rating C:19500 N; |
| Z-507333.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | S:4.763 mm; da:109.537 mm; P60°:308 kN; Max. speed for Taconite seal:700 r/min; P150°:118 kN; h:60.325 mm; Cap bolt recommended tightening torque:515.2 N·m; H2:60.325 mm; H:292.1 mm; Taconite seal:TER 115; R1:79.375 mm; Ca:73.812 mm; RG:1/2 NPT; Housing:SSAFS 526; Pa:24.9 kN; Da:230 mm; P180°:151 kN; Eye bolt:2 x 3/8-16 UNC; End plug (suffix Y):EPR 15; ba:57.944 mm; |
| 160RV2302 NSK ROLL NECK BEARINGS for ROLLING MILL | Tolerance shaft:f7 m/s; Tolerance housing:H7 m/s; Coefficient of friction µ min.:0.08; Permissible sliding velocity v min.:0 m/s; Permissible sliding velocity v max.:1 m/s; Mass bushing:0.017 kg; D:23 mm; Coefficient of friction µ max.:0.15; Specific static load factor K0:120 N/mm²; d:20 mm; Specific dynamic load factor K:40 N/mm²; B:20 mm; |
| 230RV3301 NSK ROLL NECK BEARINGS for ROLLING MILL | D:110.0000 mm; Oil Speed Rating n2:5300 rpm; Grease Speed Rating n1:4000 rpm; Fillet Radius ra:2.00 mm; d:50.000 mm; Basic Dynamic Radial Load Rating C:95200 N; Basic Static Radial Load Rating Co:95000 N; Accessories:One Shield & Snap-Ri; B:47.60 mm; Sealed Speed Rating n3:4000 rpm; |
| 145RV2101 NSK ROLL NECK BEARINGS for ROLLING MILL | H2:19 mm; Limiting speed:1100 r/min; N:21 mm; d:34.925 mm; Fatigue load limit Pu:0.655 kN; Recommended diameter for attachment bolts, mm G:12 mm; Housing:SY 507 M/VZ033; Mass bearing unit:1.5 kg; L:160 mm; H1:47.6 mm; B1:39.5 mm; Housing material:Cast iron; H:93 mm; Recommended tightening torque for grub screw:7.4 N·m; J6:146 mm; N4:4 mm; s1:24.3 mm; A:45 mm; N1:14 mm; A1:27 mm; |
| 190RV2701 NSK ROLL NECK BEARINGS for ROLLING MILL | Tolerance shaft:f7 m/s; B:55 mm; Coefficient of friction µ min.:0.08; Specific static load factor K0:120 N/mm²; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7 m/s; d:65 mm; Coefficient of friction µ max.:0.15; Mass bushing:0.26 kg; D:70 mm; Specific dynamic load factor K:40 N/mm²; Permissible sliding velocity v max.:1 m/s; |
| Z-508727.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Appropriate attachment bolt size G:1 in; Stabilizing ring:SR-34-0; P180°:92.5 kN; End plug (suffix Y):EPR 18; H1:179.375 mm; A1:171.45 mm; H2:69.85 mm; P120°:85.9 kN; Da:309.999 mm; PG:1/4 NPT; P60°:234 kN; J max.:549.275 mm; Pa:56 kN; Eye bolt:2 x 3/8-16 UNC; R1:115.888 mm; J1:107.95 mm; H:360.363 mm; h:54.769 mm; Cap bolt, SAE grade:5; Mass pillow block:132 kg; |
| 22248CAW33C3 SKF MINING MACHINERY BEARINGS | A2:304.8 mm; H1:241.3 mm; Housing:SAW 244; PG:1/4 NPT; J max.:708.025 mm; Max. speed for PosiTrac Plus seal:600 r/min; S:4.763 mm; L:831.85 mm; Stabilizing ring:SR-44-38; h:80.963 mm; Initial grease fill:2749.95 g; A1:222.25 mm; Ca:153.797 mm; P150°:145 kN; Cap bolt, SAE grade:5; J min.:628.65 mm; R1:130.175 mm; N1:41.275 mm; End plug (suffix Y):EPR 24; RG:1 NPT; |