| 22380CAW33C3 SKF MINING MACHINERY BEARINGS | s:77.787 mm; d2:155.575 mm; A1:136.525 mm; J min.:333.375 mm; H1:120.65 mm; L:422.275 mm; J max.:368.3 mm; Limiting speed:1900 r/min; Basic dynamic load rating C:408 kN; J1:63.5 mm; H2:69.85 mm; A:117.475 mm; B:155.575 mm; Attachment bolt diameter G:19.05 mm; H:247.65 mm; da:112.713 mm; Mass bearing unit:32.3 kg; S:0.794 mm; |
| 22328CAW33C3 SKF MINING MACHINERY BEARINGS | Sealed Speed Rating n3:1800 rpm; Accessories:No Shield, no Seal,; B:82.60 mm; d:100.000 mm; Grease Speed Rating n1:1800 rpm; Basic Dynamic Radial Load Rating C:255000 N; Fillet Radius ra:2.50 mm; Basic Static Radial Load Rating Co:255000 N; Oil Speed Rating n2:2600 rpm; D:215.0000 mm; |
| 23156CAW33C3 SKF MINING MACHINERY BEARINGS | Coefficient of friction µ min.:0.08; B1:10 mm; D1:180 mm; Coefficient of friction µ max.:0.15; α:124 °; D:170 mm; d:150 mm; B:70 mm; Tolerance housing:H7; Mass bushing:3.45 kg; Permissible sliding velocity v max.:0.5 m/s; h:152 mm; a:3.5 mm; Permissible sliding velocity v min.:0 m/s; Specific static load factor K0:45 N/mm²; Tolerance shaft:e7; Specific dynamic load factor K:25 N/mm²; |
| 22330CAW33C3 SKF MINING MACHINERY BEARINGS | Oil Speed Rating Open/Shielded n2:3200 rpm; d:160.000 mm; D:220.0000 mm; Grease Speed Rating Open/Shielded n1:2600 rpm; Basic Dynamic Radial Load Rating C:92300 N; Sealed Speed Rating n3:1700 rpm; Basic Static Radial Load Rating Co:98000 N; Fillet Radius ra:2.00 mm; B:28.00 mm; Accessories:One Seal; |
| 220RV3101 NSK ROLL NECK BEARINGS for ROLLING MILL | Pa:22.2 kN; Stabilizing ring:2 x 36053-50; A1:120.65 mm; Housing:SSAFS 028 KA; Da:210 mm; Mass pillow block:61.2 kg; R1:79.375 mm; H1:133.35 mm; RG:1/2 NPT; h:46.038 mm; H:257.175 mm; End plug (suffix Y):EPR 27; Ca:72.619 mm; A2:190.5 mm; P90°:149 kN; Labyrinth ring:2 x LOR 122; da:125.412 mm; P180°:107 kN; Cap bolt:5/8-11 UNC; P60°:249 kN; |
| 23152CAW33C3 SKF MINING MACHINERY BEARINGS | Mass bushing:0.001 kg; D:8 mm; Coefficient of friction µ min.:0.05; Coefficient of friction µ max.:0.1; Permissible sliding velocity v min.:0.25 m/s; B:6 mm; Specific dynamic load factor K:10 N/mm²; Tolerance shaft:h8; d:4 mm; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; Specific static load factor K0:20 N/mm²; |
| 23136CAW33C3 SKF MINING MACHINERY BEARINGS | Pa:58.7 kN; PG:1/4 NPT; H:422.275 mm; Cap bolt:4 x 7/8-9 UNC; Da:359.999 mm; A2:285.75 mm; J max.:635 mm; Housing:SAF 540; P60°:364 kN; h:62.706 mm; Eye bolt:2 x 1/2-13 UNC; Mass pillow block:195 kg; P180°:145 kN; Cap bolt recommended tightening torque:271.2 N·m; Max. speed for PosiTrac Plus seal:800 r/min; Appropriate attachment bolt size G:1.25 in; S:4.763 mm; Cap bolt, SAE grade:5; |
| 22356CAW33C3 SKF MINING MACHINERY BEARINGS | Basic Static Radial Load Rating Co:102000 N; B:54.00 mm; D:110.0000 mm; Fillet Radius ra:2.00 mm; Fillet Radius rb:1.00 mm; Grease Speed Rating n1:4300 rpm; d:50.000 mm; Oil Speed Rating n2:5600 rpm; Basic Dynamic Radial Load Rating C:119000 N; |
| 280RV3903 NSK ROLL NECK BEARINGS for ROLLING MILL | P180°:96.1 kN; L:539.75 mm; da:133.35 mm; Mass pillow block:91.6 kg; PG:1/4 NPT; A2:279.4 mm; Eye bolt:2 x 3/8-16 UNC; Cap bolt, SAE grade:5; N1:28.575 mm; Ca:82.804 mm; Appropriate attachment bolt size G:1 in; P120°:87.2 kN; J min.:431.8 mm; Housing:SAF 530; Initial grease fill:623.7 g; J1:95.25 mm; P90°:138 kN; Stabilizing ring:SR-30-0; R2:39.688 mm; S:4.763 mm; |
| 22320CAW33C3 SKF MINING MACHINERY BEARINGS | Fillet Radius ra:1.00 mm; B:19.00 mm; D:72.0000 mm; Oil Speed Rating n2:11000 rpm; Grease Speed Rating n1:8000 rpm; Basic Static Radial Load Rating Co:19600 N; Basic Dynamic Radial Load Rating C:32500 N; d:30.000 mm; |
| 23140CAW33C3 SKF MINING MACHINERY BEARINGS | B:13 mm; F:14 mm; Mass inner ring:0.0074 kg; d:10 mm; r, r1,2 min.:0.3 mm; |
| 23130CAW33C3 SKF MINING MACHINERY BEARINGS | Basic Interchange:-; Basic Radial Load Rating-Static SCO:48600 lbf; Accessories:Mast Guide Type- 307; Basic Radial Load Rating-Dynamic DC:13600 lbf; Basic Interchange BCA:-; Basic Interchange NDH:-; Basic Interchange NSK:-; Basic Interchange MCGILL:-; Basic Interchange SPLIT:-; |