| 313824 KOYO ROLL NECK BEARINGS for ROLLING MILL | Mass housing:69.5 kg; J:430 mm; J6:470 mm; Oil seal:2 x TSD 3036 U; P90°:1000 kN; Oil level, max.:54 mm; P55°:2100 kN; A1:180 mm; H:333 mm; Locating ring:2 x FRB 17/280; Cap bolt, rec. tightening torque:350 N·m; J1:100 mm; Q120°:1800 kN; Ca:108 mm; Q150°:1040 kN; A:226 mm; H1:170 mm; H2:70 mm; Appropriate attachment bolt, rec. tightening torque:665 N·m; Appropriate attachment bolt, size G:24 mm; |
| 190RV2601 NSK ROLL NECK BEARINGS for ROLLING MILL | Mass inner ring:0.43 kg; F:105 mm; d:95 mm; B:36 mm; r, r1,2 min.:1 mm; |
| Z-512764.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Labyrinth ring (dc shaft position):LOR 37; Ca:39.014 mm; P180°:19.1 kN; Initial grease fill:107.73 g; Cap bolt:2 x 1/2-13 UNC; Labyrinth ring (db shaft position):LOR 55; RG:1/8 NPT; Da:120 mm; Housing:SAF 213; R2:15.875 mm; Pa:12 kN; Mass pillow block:9.07 kg; PG:1/8 NPT; db:77.787 mm; P90°:30.2 kN; N1:19.05 mm; H:147.637 mm; H1:76.2 mm; PosiTrac Plus contact element (db shaft position):B10724-53; |
| 160RV2301 NSK ROLL NECK BEARINGS for ROLLING MILL | Minimum axial load factor A:25.92; B:48.5 mm; ra max.:5 mm; Basic dynamic load rating C:3450 kN; D:540 mm; Fatigue load limit Pu:1320 kN; D1:305 mm; Basic static load rating C0:18000 kN; Mass bearing:153 kg; Reference speed:280 r/min; d:300 mm; Da max.:331 mm; r1,2 min.:6 mm; H:145 mm; d1:537 mm; Limiting speed:530 r/min; da min.:533 mm; |
| 145RV2201 NSK ROLL NECK BEARINGS for ROLLING MILL | B:42.90 mm; Accessories:Two Seals; Basic Dynamic Radial Load Rating C:80900 N; Grease Speed Rating n1:4500 rpm; d:45.000 mm; Fillet Radius ra:1.50 mm; Oil Speed Rating n2:6000 rpm; Sealed Speed Rating n3:4500 rpm; Basic Static Radial Load Rating Co:80000 N; D:100.0000 mm; |
| Z-543975.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | d1:220 mm; Da max.:480 mm; Limiting speed:1300 r/min; db min.:257 mm; d3:300 mm; Calculation factor Y1:2.2; D:500 mm; Calculation factor e:0.31; Calculation factor Y0:2.2; B:155 mm; d2 ≈:303 mm; Basic static load rating C0:4000 kN; Ba min.:11 mm; D1 ≈:423 mm; B1:199 mm; K:12 mm; Basic dynamic load rating C:3229 kN; Reference speed:950 r/min; b:22.3 mm; Mass bearing + sleeve:170 kg; |
| 23130CAW33C3 SKF MINING MACHINERY BEARINGS | Basic Interchange:-; Basic Radial Load Rating-Static SCO:48600 lbf; Accessories:Mast Guide Type- 307; Basic Radial Load Rating-Dynamic DC:13600 lbf; Basic Interchange BCA:-; Basic Interchange NDH:-; Basic Interchange NSK:-; Basic Interchange MCGILL:-; Basic Interchange SPLIT:-; |
| Z-507344.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | H2:47.625 mm; H:160.338 mm; Limiting speed:2800 r/min; Mass bearing unit:10.9 kg; B:92.075 mm; A1:99.219 mm; H1:79.375 mm; L:304.8 mm; J max.:247.65 mm; J min.:234.95 mm; S:0.794 mm; d2:111.125 mm; da:74.612 mm; Basic dynamic load rating C:158 kN; s:31.75 mm; Attachment bolt diameter G:19.05 mm; A:76.2 mm; |
| Z-512580.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | d:55.000 mm; Grease Speed Rating n1:3800 rpm; B:49.20 mm; Basic Static Radial Load Rating Co:81500 N; Basic Dynamic Radial Load Rating C:106000 N; Fillet Radius ra:2.00 mm; Oil Speed Rating n2:5000 rpm; Sealed Speed Rating n3:3800 rpm; Accessories:Shield & Seal; D:120.0000 mm; |
| 190RV2701 NSK ROLL NECK BEARINGS for ROLLING MILL | Tolerance shaft:f7 m/s; B:55 mm; Coefficient of friction µ min.:0.08; Specific static load factor K0:120 N/mm²; Permissible sliding velocity v min.:0 m/s; Tolerance housing:H7 m/s; d:65 mm; Coefficient of friction µ max.:0.15; Mass bushing:0.26 kg; D:70 mm; Specific dynamic load factor K:40 N/mm²; Permissible sliding velocity v max.:1 m/s; |
| 4R6819 NTN ROLL NECK BEARINGS for ROLLING MILL | Mass bearing unit:1.2 kg; Recommended diameter for attachment bolts, inch G:0.5 in; Limiting speed:1100 r/min; T:46.4 mm; Basic static load rating C0:15.3 kN; Da:88.9 mm; J7:15 mm; J6:106 mm; A1:13 mm; s1:25.4 mm; Recommended tightening torque for grub screw:6.5 N·m; Housing material:Cast iron; H:156 mm; Db1:88 mm; L:96 mm; B4:6 mm; Db2:96 mm; d:34.925 mm; Hexagonal key size for grub screw N:3.969 mm; |
| 23152CAW33C3 SKF MINING MACHINERY BEARINGS | Mass bushing:0.001 kg; D:8 mm; Coefficient of friction µ min.:0.05; Coefficient of friction µ max.:0.1; Permissible sliding velocity v min.:0.25 m/s; B:6 mm; Specific dynamic load factor K:10 N/mm²; Tolerance shaft:h8; d:4 mm; Tolerance housing:H7; Permissible sliding velocity v max.:5 m/s; Specific static load factor K0:20 N/mm²; |