| Z-512764.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Labyrinth ring (dc shaft position):LOR 37; Ca:39.014 mm; P180°:19.1 kN; Initial grease fill:107.73 g; Cap bolt:2 x 1/2-13 UNC; Labyrinth ring (db shaft position):LOR 55; RG:1/8 NPT; Da:120 mm; Housing:SAF 213; R2:15.875 mm; Pa:12 kN; Mass pillow block:9.07 kg; PG:1/8 NPT; db:77.787 mm; P90°:30.2 kN; N1:19.05 mm; H:147.637 mm; H1:76.2 mm; PosiTrac Plus contact element (db shaft position):B10724-53; |
| Z-507735.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Da max.:541 mm; Fatigue load limit Pu:57 kN; H:80 mm; Minimum load factor A:67; Basic dynamic load rating C:553 kN; Basic static load rating C0:3600 kN; r1,2 min.:2.1 mm; ra max.:2 mm; D1 ≈:504 mm; d1 ≈:596 mm; D:600 mm; Reference speed:560 r/min; Limiting speed:800 r/min; Mass bearing (including seat washer where applicable):47 kg; da min.:559 mm; d:500 mm; |
| 4R5611 NTN ROLL NECK BEARINGS for ROLLING MILL | Calculation factor Y0:2; Comparative radial load rating CF:1760 kN; T:285.75 mm; Thrust factor K:1.76; Basic static load rating C0:18000 kN; d:571.5 mm; Calculation factor e:0.33; D1 ≈:720 mm; D:812.8 mm; Calculation factor Y2:3; Basic dynamic load rating C:7210 kN; Design variant/feature:TDI/GWIY2; r3,4 min.:6.4 mm; B:285.75 mm; Calculation factor Y1:2; d1 ≈:621 mm; Comparative axial load rating CFa:580 kN; |
| 22352CAW33C3 SKF MINING MACHINERY BEARINGS | Permissible sliding velocity v min.:0 m/s; Tolerance shaft:h9; Tolerance housing:H7; Permissible sliding velocity v max.:1 m/s; Specific dynamic load factor K:40 N/mm²; D:17 mm; d:15 mm; Specific static load factor K0:80 N/mm²; Coefficient of friction µ max.:0.15; Mass bushing:0.0011 kg; B:15 mm; Coefficient of friction µ min.:0.06; |
| Z-527634.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Reference speed:180 r/min; Minimum load factor A:2900; Fatigue load limit Pu:208 kN; Da max.:1495 mm; D1 ≈:1408 mm; Limiting speed:260 r/min; d1 ≈:1622 mm; ra max.:6 mm; H:180 mm; D:1630 mm; Basic dynamic load rating C:1820 kN; Basic static load rating C0:22000 kN; da min.:1535 mm; Mass bearing (including seat washer where applicable):665 kg; d:1400 mm; r1,2 min.:8 mm; |
| 4R2904 NTN ROLL NECK BEARINGS for ROLLING MILL | Bolt Pattern C:0.55 in; Height G:3.438 in; Travel:6; Frame Size B:12 in; Frame Accepts These Shaft Sizes (Bearing Bore):30 mm, 35 mm; Shaft C/L Distance F:1 27/32 in; Bolt Pattern E:10 1/2 in; Frame Size A:4 41/64 in; Bolt Pattern D:2 3/4 in; |
| 38FC26168-1 KOYO ROLL NECK BEARINGS for ROLLING MILL | Basic Dynamic Radial Load Rating C:66000 N; Sealed Speed Rating n3:4300 rpm; D:100.0000 mm; Oil Speed Rating n2:5600 rpm; Basic Static Radial Load Rating Co:76500 N; d:55.000 mm; Grease Speed Rating n1:4300 rpm; Fillet Radius ra:1.50 mm; Accessories:Two Seals & Snap-Rin; B:33.30 mm; |
| 4R4426 NTN ROLL NECK BEARINGS for ROLLING MILL | d3 max.:155.702 mm; Hydraulic nut:HMVC 26E; Sleeve:S 3026x4.3/8; Threads per inch:12; G:129.692 mm; d1:111.125 mm; B4:25.4 mm; B:22.479 mm; B1:81.966 mm; d:130 mm; Mass adapter sleeve assembly:3.4 kg; |
| 23138CAW33C3 SKF MINING MACHINERY BEARINGS | C:42.85 mm; b:5.7 mm; ra max.:1 mm; α:5 °; Sealing solution:Double-lip seals; Material constant KM:330; Design (sliding contact surface combination):Steel/steel; da max.:70.1 mm; b1:5 mm; Specific dynamic load factor K:100 N/mm²; Basic dynamic load rating C:280 kN; r2 min.:1 mm; Basic static load rating C0:850 kN; Da max.:85.3 mm; d1 ≈:70.104 mm; B:85.725 mm; d:57.15 mm; D:90.488 mm; |
| 150RV2302 NSK ROLL NECK BEARINGS for ROLLING MILL | Sealed Speed Rating n3:3600 rpm; d:80.000 mm; Grease Speed Rating Open/Shielded n1:6000 rpm; Fillet Radius ra:0.60 mm; D:100.0000 mm; Oil Speed Rating Open/Shielded n2:7000 rpm; Basic Static Radial Load Rating Co:13700 N; B:10.00 mm; Accessories:One Shield; Basic Dynamic Radial Load Rating C:13000 N; |
| 22244CAKW33C3 SKF MINING MACHINERY BEARINGS | Stabilizing ring:SR-28-0; Max. speed for PosiTrac Plus seal:1150 r/min; Appropriate attachment bolt size G:1 in; Ca:77.8 mm; L:511.175 mm; J1:85.725 mm; H:298.45 mm; R2:38.1 mm; Da:250 mm; ba:61.119 mm; Mass pillow block:92.5 kg; A1:149.225 mm; Cap bolt, SAE grade:8; RG:3/4 NPT; h:51.594 mm; Initial grease fill:481.95 g; N1:28.575 mm; P60°:301 kN; J max.:434.975 mm; Cap bolt:7/8-9 UNC; |
| Z-510150.02.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Grease Speed Rating n1:1700 rpm; Fillet Radius rb:1.00 mm; Basic Static Radial Load Rating Co:850000 N; D:320.0000 mm; B:140.00 mm; Oil Speed Rating n2:2100 rpm; Fillet Radius ra:3.00 mm; Basic Dynamic Radial Load Rating C:520000 N; d:110.000 mm; |