| 23144CAW33C3 SKF MINING MACHINERY BEARINGS | B:6.00 mm; Grease Speed Rating Open/Shielded n1:36000 rpm; Oil Speed Rating Open/Shielded n2:43000 rpm; D:19.0000 mm; Basic Static Radial Load Rating Co:950 N; Basic Dynamic Radial Load Rating C:2210 N; Fillet Radius ra:0.30 mm; Accessories:Two Seals; Sealed Speed Rating n3:26000 rpm; d:5.000 mm; |
| Z-507735.ZL FAG ROLL NECK BEARINGS for ROLLING MILL | Da max.:541 mm; Fatigue load limit Pu:57 kN; H:80 mm; Minimum load factor A:67; Basic dynamic load rating C:553 kN; Basic static load rating C0:3600 kN; r1,2 min.:2.1 mm; ra max.:2 mm; D1 ≈:504 mm; d1 ≈:596 mm; D:600 mm; Reference speed:560 r/min; Limiting speed:800 r/min; Mass bearing (including seat washer where applicable):47 kg; da min.:559 mm; d:500 mm; |
| 68FC48350D KOYO ROLL NECK BEARINGS for ROLLING MILL | Coefficient of friction µ max.:0.1; Mass bushing:0.026 kg; Permissible sliding velocity v min.:0.25 m/s; Specific static load factor K0:20 N/mm²; Coefficient of friction µ min.:0.05; Permissible sliding velocity v max.:5 m/s; Tolerance shaft:h8; d:15 mm; D:20 mm; Tolerance housing:H7; Specific dynamic load factor K:10 N/mm²; B:30 mm; |
| 23148CAW33C3 SKF MINING MACHINERY BEARINGS | Bore Diameter D:20 mm; Outher Width C:14 mm; Dimension S:12.7 mm; Basic Dynamic Radial Load Rating:10600 N; Inner Width B:31.0 mm; Set Screw Size SSS:M6*0.75*5; Max Fillet Rad. MFR:0.6 mm; Dimension D3:28.20 mm; Outside Diameter D2:47 mm; Basic Static Radial Load Rating Co:6550 N; Weight W:0.14 kg; |
| 150RV2302 NSK ROLL NECK BEARINGS for ROLLING MILL | Sealed Speed Rating n3:3600 rpm; d:80.000 mm; Grease Speed Rating Open/Shielded n1:6000 rpm; Fillet Radius ra:0.60 mm; D:100.0000 mm; Oil Speed Rating Open/Shielded n2:7000 rpm; Basic Static Radial Load Rating Co:13700 N; B:10.00 mm; Accessories:One Shield; Basic Dynamic Radial Load Rating C:13000 N; |
| 22360CAW33C3 SKF MINING MACHINERY BEARINGS | J max.:279.4 mm; L:330.2 mm; P120°:21.8 kN; PG:1/8 NPT; Ca:57.785 mm; Da:140 mm; P150°:19.6 kN; A2:209.55 mm; P60°:60.5 kN; N1:19.05 mm; R1:53.181 mm; h:36.513 mm; Cap bolt, SAE grade:8; Stabilizing ring:2 x SR-1613; Mass pillow block:17.1 kg; Pa:6.49 kN; RG:3/8 NPT; P90°:36 kN; Cap bolt recommended tightening torque:298.3 N·m; Max. speed for Taconite seal:1400 r/min; |
| 22248CAW33C3 SKF MINING MACHINERY BEARINGS | A2:304.8 mm; H1:241.3 mm; Housing:SAW 244; PG:1/4 NPT; J max.:708.025 mm; Max. speed for PosiTrac Plus seal:600 r/min; S:4.763 mm; L:831.85 mm; Stabilizing ring:SR-44-38; h:80.963 mm; Initial grease fill:2749.95 g; A1:222.25 mm; Ca:153.797 mm; P150°:145 kN; Cap bolt, SAE grade:5; J min.:628.65 mm; R1:130.175 mm; N1:41.275 mm; End plug (suffix Y):EPR 24; RG:1 NPT; |
| 23140CAW33C3 SKF MINING MACHINERY BEARINGS | B:13 mm; F:14 mm; Mass inner ring:0.0074 kg; d:10 mm; r, r1,2 min.:0.3 mm; |
| 22252CAW33C3 SKF MINING MACHINERY BEARINGS | Grease Speed Rating n1:3600 rpm; Basic Static Radial Load Rating Co:106000 N; Basic Dynamic Radial Load Rating C:88000 N; D:120.0000 mm; Oil Speed Rating n2:4800 rpm; Fillet Radius ra:1.50 mm; B:38.10 mm; d:65.000 mm; Sealed Speed Rating n3:3600 rpm; Accessories:Two Shields; |
| 4R6819 NTN ROLL NECK BEARINGS for ROLLING MILL | Mass bearing unit:1.2 kg; Recommended diameter for attachment bolts, inch G:0.5 in; Limiting speed:1100 r/min; T:46.4 mm; Basic static load rating C0:15.3 kN; Da:88.9 mm; J7:15 mm; J6:106 mm; A1:13 mm; s1:25.4 mm; Recommended tightening torque for grub screw:6.5 N·m; Housing material:Cast iron; H:156 mm; Db1:88 mm; L:96 mm; B4:6 mm; Db2:96 mm; d:34.925 mm; Hexagonal key size for grub screw N:3.969 mm; |
| NU2330C4 SKF MINING MACHINERY BEARINGS | Pa:81.4 kN; Appropriate attachment bolt size G:1.5 in; ba:96.838 mm; Cap bolt recommended tightening torque:400 N·m; H1:241.3 mm; P120°:160 kN; PG:1/4 NPT; Stabilizing ring:2 x A8898; Eye bolt:2 x 1/2-13 UNC; h:69.85 mm; Mass pillow block:247 kg; J min.:628.65 mm; RG:1 NPT; A1:222.25 mm; P90°:254 kN; Cap bolt, SAE grade:5; P150°:145 kN; P60°:423 kN; R1:130.175 mm; Da:399.999 mm; |
| 160RV2301 NSK ROLL NECK BEARINGS for ROLLING MILL | Minimum axial load factor A:25.92; B:48.5 mm; ra max.:5 mm; Basic dynamic load rating C:3450 kN; D:540 mm; Fatigue load limit Pu:1320 kN; D1:305 mm; Basic static load rating C0:18000 kN; Mass bearing:153 kg; Reference speed:280 r/min; d:300 mm; Da max.:331 mm; r1,2 min.:6 mm; H:145 mm; d1:537 mm; Limiting speed:530 r/min; da min.:533 mm; |